How to Fix 092-670 to 092-673 092-675 to 092-678 Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?

Posted by Xwk Tech on


092-670 to 673, 092-675 to 678 ADC Patch Fail RAP

BSD-ON: BSD 9.9 ADC and Environment Sensing, BSD 9.4 Development (1 of 2).

092-670 The yellow ADC electric patch is abnormally light or a fault in the ADC sensor was detected.
092-671 The magenta ADC electric patch is abnormally light or a fault in the ADC sensor was detected.
092-672 The cyan ADC electric patch is abnormally light or a fault in the ADC sensor was detected.
092-673 The black ADC electric patch is abnormally light or a fault in the ADC sensor was detected.
092-675 The yellow ADC tone patch is abnormally light or a fault in the ADC sensor was detected.
092-676 The yellow ADC tone patch is abnormally light or a fault in the ADC sensor was detected.
092-677 The yellow ADC tone patch is abnormally light or a fault in the ADC sensor was detected.
092-678 The yellow ADC tone patch is abnormally light or a fault in the ADC sensor was detected.

Initial Actions

• Perform IQ1 to check for a low density color or white vertical streaks image quality defect.
• Enter dC125. Check for the below faults and perform the applicable procedures as necessary:

042-325 Main Motor Fail RAP
043-342 Sub Motor Fail RAP
– 061-xxx(061-354 061-358) LPH System Fail RAPs
– 089-xxx(089-600 089-601 089-604 089-616 089-617) Registration Control System Failure RAPs
093-400, 093-406 to 093-409 Toner Cartridge Near End of Life RAP
094-420, 094-422 IBT Belt Unit / 2nd BTR Roll End of Life RAP

Procedure

WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.

Perform the steps that follow:

1. Switch off, then switch on the machine, GP 10.
2. If the fault persists, replace a new cartridge CRUM (toner chip or drum chip) listed as below or install new components as necessary:

• MOB ADC sensor assembly, PL 90.40 Item 6. Enter dC675, perform the registration control setup cycle.
• IBT belt unit, PL 90.45 Item 1.

NOTE: Following installation of the new IBT belt unit, enter dC135 code 954-820 to reset the HFSI value for the BTR Unit.

• IBT cleaner, PL 90.45 Item 2.
• Toner cartridge:

– Black toner cartridge, PL 90.05 Item 13.
– Yellow toner cartridge, PL 90.05 Item 10.
– Magenta toner cartridge, PL 90.05 Item 11.
– Cyan toner cartridge, PL 90.05 Item 12.

• Drum cartridge:

– Black drum cartridge, PL 90.20 Item 5.
– Yellow drum cartridge, PL 90.20 Item 8.
– Magenta drum cartridge, PL 90.20 Item 7.
– Cyan drum cartridge, PL 90.20 Item 6.

• LPH, PL 60.35 Item 1.
• LPH FFC:

– Black LPH FFC, PL 60.35 Item 4.
– Cyan LPH FFC, PL 60.35 Item 5.
– Magenta LPH FFC, PL 60.35 Item 6.
– Yellow LPH FFC, PL 60.35 Item 7.

• HVPS, PL 1.05 Item 7.
• Drive PWB, PL 1.10 Item 4.

**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**

You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.

Toner Chip (For North America and West Europe Region):

106R03741 106R03744 106R03743 106R03742
106R03757 106R03760 106R03759 106R03758
106R03737 106R03740 106R03739 106R03738

Toner Chip (For South America and East Europe Region):

106R03749 106R03752 106R03751 106R03750
106R03745 106R03748 106R03747 106R03746
106R03765 106R03768 106R03767 106R03766

Toner Chip (For Metered Machine):

106R03733 106R03736 106R03735 106R03734

Drum Chip:

113R00780 113R00782


Share this post



← Older Post Newer Post →


Leave a comment