Articles

012-211 Stacker Tray Fail Entry RAP012-211 This fault is raised when:• Within a specified time after the stacker tray started lifting up, the stack height sensor did not detect the lifting up of the stacker tray.• Within a specified time after the stacker tray started going down at initialization and during a job, the lower position of the tray (full) could not be detected based on the changes in the stacker stack sensor 1 and the stacker stack sensor 2.ProcedureGo to the relevant procedure:• Integrated office finisher installed, 012-211A Stacker Tray Fail RAP.• Office finisher LX installed, 012-211B Stacker Tray...

012-210B NVM Fail RAPBSD-ON: BSD 3.6 PWB Communications (ESS PWB/Drive PWB to Finisher)ProcedureNOTE: Ensure the correct RAP is performed, refer to the 012-210 NVM Fail Entry RAP.WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Check the wiring between the finisher and the IOT.2. If the fault persists, install a new finisher PWB, PL 13.45 Item 2.**This RAP is from Xerox Service Manual. All brand names and...

012-210A NVM Fail RAPBSD-ON: BSD 3.6 PWB Communications (ESS PWB/Drive PWB to Finisher)ProcedureNOTE: Ensure the correct RAP is performed, refer to the 012-210 NVM Fail Entry RAP.WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Check the wiring between the finisher and the IOT.2. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.**This RAP is from Xerox Service Manual. All brand names and...

012-210 NVM Fail Entry RAP012-210 An error is detected at NVM access.ProcedureGo to the relevant procedure:• Integrated office finisher installed, 012-210A NVM Fail RAP.• Office finisher LX installed, 012-210B NVM Fail RAP.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749 106R03752 106R03751 106R03750• 106R03745 106R03748...

012-189B Finisher Jam RAPProcedureClear the paper jam and repeat the job.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749 106R03752 106R03751 106R03750• 106R03745 106R03748 106R03747 106R03746• 106R03765 106R03768 106R03767 106R03766Toner Chip (For Metered Machine):• 106R03733 106R03736 106R03735 106R03734Drum Chip:• 113R00780 113R00782