Articles

016-352 Internal Network Initialize Fail RAP016-352 Internal network initialization error.ProcedurePerform the steps that follow:1. Switch off, then switch on the machine, GP 10.2. Reload the software, GP 4.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749 106R03752 106R03751 106R03750• 106R03745 106R03748 106R03747 106R03746• 106R03765 106R03768...

016-335 to 016-351 Controller Fail RAP016-335 Cont program ROM diagnostic fail 1.016-336 Cont program ROM diagnostic fail 2.016-337 Cont program ROM diagnostic fail 3.016-338 Cont font ROM diagnostic fail 1.016-339 Cont font ROM diagnostic fail 2.016-340 Cont font ROM diagnostic fail 3.016-341 Cont font ROM diagnostic fail 4.016-342 Cont RTC diagnostic fail.016-343 Long boot diag timer fail.016-345 Cont NVM diagnostic fail.016-346 Cont A4 fax modem diagnosis fail.016-347 Cont page memory diagnostic fail 1.016-348 Cont page memory fail 2.016-349 Cont MAC address data fail.016-350 Cont SEEP-ROM diagnostic fail 1.016-351 Cont SEEP-ROM diagnostic fail 2.ProcedureWARNING: Ensure that the electricity to the machine...

016-330, 331, 332 Cont System Memory Fail RAP016-330 Cont system memory diagnostic fail 1.016-331 Cont system memory diagnostic fail 2.016-332 Cont system memory diagnostic fail 3.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Switch off, then switch on the machine, GP 10.2. Ensure that all connectors on the ESS PWB, PL 3.10 Item 6 are securely connected. Ensure all surface mounted modules are securely connected.3. Reload...

016-327, 016-328 Connection Fail RAP016-327 Backplane connection fail.016-328 The controller has detected a failure at its cable connection with the drive PWB.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Switch off, then switch on the machine, GP 10.2. Ensure that all connectors on the ESS PWB, PL 3.10 Item 6 are securely connected. Ensure all surface mounted modules are securely connected.3. Reload the software, GP 4.**This...

016-326, 016-607 UI Cable Connection Fail RAPBSD-ON: BSD 2.1 Control Panel016-326 The controller has detected a failure at its cable connection with the UI.016-607 Cont-UI Cable Connection FailProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Check the wiring between the ESS PWB and the UI2. Install new components as necessary:• ESS PWB, PL 3.10 Item 6.• UI assembly (C7030F), PL 2.05 Item 7.• UI assembly (C7000),...