How to Fix 01A Error for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
01A AC Power RAP
BSD-ON: BSD 1.1.Main Power On (1 of 2)
BSD-ON: BSD 1.2 Main Power On (2 of 2)
Use this procedure to identify AC power input and output failures.
Procedure
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
WARNING: Take care when measuring AC mains (line) voltage. Electricity can cause death or injury.
1. Switch off the main power switch, GP 10. Check the voltage between J10 and J18 on the inlet GFI breaker. The voltage measured is within electrical power requirements, GP 17. If YES, go to 7, if NO, go to 2.
2. Disconnect the power cord from the outlet. Check the AC mains (line) voltage at the customers power outlet. The voltage measured is within electrical power requirements, GP 17. If YES, go to 4, if NO, go to 3.
3. If the voltage is incorrect, or the wiring of the main supply is found to be defective, inform your technical manager and the customer. Do not attempt to repair or adjust the customer supply.
4. Check the power cord for open circuit and poor contact. The main power cord is good. If YES, go to 6, if NO, go to 5.
5. Install a new power cord.
6. Install a new inlet GFI breaker, PL 1.15 Item 7.
7. Switch on the main power switch, GP 10. Check the voltage between P1 pin 1 and pin 3 on the LVPS. The AC power supply is within specification, GP 17. If YES, go to 9, if NO, go to 8.
8. Switch off the power, then unplug the power cord from the outlet. Check the wiring:
• Between the GFI breaker (J10 pin 1) and the main power switch (P/J12 pin 1).
• Between the main power switch (P/J14 pin 1) and the LVPS (P1 pin 3).
• Between the inlet GFI breaker (J18 pin 1) and the LVPS (P1 pin 1).
Install new components as necessary:
• Main power switch, PL 1.05 Item 3.
• LVPS, PL 1.10 Item 3.
9. Check the AC circuit to each component. Refer to the Wiring Diagrams.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON: BSD 1.1.Main Power On (1 of 2)
BSD-ON: BSD 1.2 Main Power On (2 of 2)
Use this procedure to identify AC power input and output failures.
Procedure
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
WARNING: Take care when measuring AC mains (line) voltage. Electricity can cause death or injury.
1. Switch off the main power switch, GP 10. Check the voltage between J10 and J18 on the inlet GFI breaker. The voltage measured is within electrical power requirements, GP 17. If YES, go to 7, if NO, go to 2.
2. Disconnect the power cord from the outlet. Check the AC mains (line) voltage at the customers power outlet. The voltage measured is within electrical power requirements, GP 17. If YES, go to 4, if NO, go to 3.
3. If the voltage is incorrect, or the wiring of the main supply is found to be defective, inform your technical manager and the customer. Do not attempt to repair or adjust the customer supply.
4. Check the power cord for open circuit and poor contact. The main power cord is good. If YES, go to 6, if NO, go to 5.
5. Install a new power cord.
6. Install a new inlet GFI breaker, PL 1.15 Item 7.
7. Switch on the main power switch, GP 10. Check the voltage between P1 pin 1 and pin 3 on the LVPS. The AC power supply is within specification, GP 17. If YES, go to 9, if NO, go to 8.
8. Switch off the power, then unplug the power cord from the outlet. Check the wiring:
• Between the GFI breaker (J10 pin 1) and the main power switch (P/J12 pin 1).
• Between the main power switch (P/J14 pin 1) and the LVPS (P1 pin 3).
• Between the inlet GFI breaker (J18 pin 1) and the LVPS (P1 pin 1).
Install new components as necessary:
• Main power switch, PL 1.05 Item 3.
• LVPS, PL 1.10 Item 3.
9. Check the AC circuit to each component. Refer to the Wiring Diagrams.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782