How to Fix 012-260 012-282 Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
012-260, 012-282 Eject Clamp Home Sensor Fail RAP
BSD-ON: BSD 13.13 Office Finisher LX Eject Control (1 of 2)
012-260 After the eject clamp started ascending, the eject clamp home sensor did not turn on within 500ms.
012-282 After the eject clamp started descending, the eject clamp home sensor did not turn off within 200ms.
Initial Actions
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Manually operate the eject mechanism. Check for binding, a dirty sensor, or damage.
• Check the actuator for the eject clamp home sensor, PL 13.27 Item 16 for damage
Procedure
1. Enter dC330 code 012-250. Actuate the eject clamp home sensor. The display changes. If YES, go to 9. If NO, go to 2.
2. Check the wiring between J8870 pin 2 on the eject clamp home sensor and P/J8988 pin 8 on the finisher PWB for an open or short circuit, or loose or damaged connectors. The wiring is good. If YES, go to 4. If NO, go to 3.
3. Reconnect or repair as necessary.
4. Measure the voltage between P/J8988 pins 9 and 7 on the finisher PWB. The voltage is approximately +5VDC. If YES, go to 6. If NO, go to 5.
5. Install a new finisher PWB, PL 13.45 Item 2.
6. Measure the voltage between P/J8988 pin 8 on the finisher PWB and ground. Actuate the eject clamp home sensor. The voltage changes. If YES, go to 8. If NO, go to 7.
7. Install a new eject clamp home sensor, PL 13.27 Item 16.
8. Install a new finisher PWB, PL 13.45 Item 2.
9. Enter dC330 code 012-052 and 012-053 alternately. The eject motor runs. If YES, go to 15. If NO, go to 10.
10. Check the wiring between P/J8878 pins 1 to 6 on the eject motor and P/J8983 pins 5 to 8 on the finisher PWB for an open or short circuit, or loose or damaged connectors. The wiring is good. If YES, go to 12. If NO, go to 11.
11. Reconnect or repair as necessary.
12. Measure the resistance of the eject motor between each pin of P/J8878 pins 1, 3, 4 and 6. The resistance is approximately 2 Ohm. If YES, go to 14. If NO, go to 13.
13. Install a new eject motor, PL 13.27 Item 4.
14. Install a new finisher PWB, PL 13.45 Item 2. If the problem persists, install a new eject motor, PL PL 13.27 Item 4.
15. Check for an intermittent circuit or intermittent mechanical problem. If the check is good, install a new finisher PWB, PL 13.45 Item 2.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON: BSD 13.13 Office Finisher LX Eject Control (1 of 2)
012-260 After the eject clamp started ascending, the eject clamp home sensor did not turn on within 500ms.
012-282 After the eject clamp started descending, the eject clamp home sensor did not turn off within 200ms.
Initial Actions
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Manually operate the eject mechanism. Check for binding, a dirty sensor, or damage.
• Check the actuator for the eject clamp home sensor, PL 13.27 Item 16 for damage
Procedure
1. Enter dC330 code 012-250. Actuate the eject clamp home sensor. The display changes. If YES, go to 9. If NO, go to 2.
2. Check the wiring between J8870 pin 2 on the eject clamp home sensor and P/J8988 pin 8 on the finisher PWB for an open or short circuit, or loose or damaged connectors. The wiring is good. If YES, go to 4. If NO, go to 3.
3. Reconnect or repair as necessary.
4. Measure the voltage between P/J8988 pins 9 and 7 on the finisher PWB. The voltage is approximately +5VDC. If YES, go to 6. If NO, go to 5.
5. Install a new finisher PWB, PL 13.45 Item 2.
6. Measure the voltage between P/J8988 pin 8 on the finisher PWB and ground. Actuate the eject clamp home sensor. The voltage changes. If YES, go to 8. If NO, go to 7.
7. Install a new eject clamp home sensor, PL 13.27 Item 16.
8. Install a new finisher PWB, PL 13.45 Item 2.
9. Enter dC330 code 012-052 and 012-053 alternately. The eject motor runs. If YES, go to 15. If NO, go to 10.
10. Check the wiring between P/J8878 pins 1 to 6 on the eject motor and P/J8983 pins 5 to 8 on the finisher PWB for an open or short circuit, or loose or damaged connectors. The wiring is good. If YES, go to 12. If NO, go to 11.
11. Reconnect or repair as necessary.
12. Measure the resistance of the eject motor between each pin of P/J8878 pins 1, 3, 4 and 6. The resistance is approximately 2 Ohm. If YES, go to 14. If NO, go to 13.
13. Install a new eject motor, PL 13.27 Item 4.
14. Install a new finisher PWB, PL 13.45 Item 2. If the problem persists, install a new eject motor, PL PL 13.27 Item 4.
15. Check for an intermittent circuit or intermittent mechanical problem. If the check is good, install a new finisher PWB, PL 13.45 Item 2.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782