How to Enter dC330 Component Control for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?

Posted by Xwk Tech on

Purpose

To show the status of input components e.g. sensors, and to run or energize output components e.g. motors, solenoids.

Description

Output and input component codes are entered into the Component Control Table on the UI, and then checked individually or in permitted groups. The codes in the tables are grouped in function chain order. Refer to GP 2 Fault Codes and History Files.

NOTE: To check the operation of the fuser temperature, tray size sensing, development housing ATC sensors and MOB sensor, refer to dC140 Analog Monitor.

Go to the appropriate procedure:

• Input Components
• Output Components

Input Components

When the appropriate code is entered, the status of the component is shown on the UI.

NOTE: The logic level shown on the BSD with the signal name is the actual signal as measured with a service meter. This is not necessarily the same as the logic state shown on the UI, especially where the output is inverted. When testing components using these control codes, look for a change in state, not for a high or low.

The displayed status of the input component can be changed by causing the component status to change, e.g. operating a sensor with a sheet of paper.

Go to the appropriate table:

• Table 1 Input codes 005.
• Table 2 Input Codes 012 - Integrated Office Finisher.
• Table 3 Input Codes 012 and 013 - Office Finisher LX.
• Table 4 Input codes 042.
• Table 5 Input Codes 062.
• Table 6 Input Codes 071 to 078.
• Table 7 Input Codes 091.

Output Components

When the appropriate code is entered, the component runs or energizes for a set time. The default timeout for most components is set at 90 seconds, but can be as short as 5 seconds. Some components require that other components are run or energized at the same time. It is possible to enter and run or energize up to 6 component control codes (not fax), but only in permitted groups. If illegal combinations of codes are entered, the components do not run or energize.

Go to the appropriate table:

• Table 8 Output Codes 005.
• Table 9 Output Codes 012 - Integrated Office Finisher.
• Table 10 Output Codes 012 and 013 - Office Finisher LX.
• Table 11 Output Codes 042.
• Table 12 Output Codes 061 and 062.
• Table 13 Output Codes 071 to 078.
• Table 14 Output Codes 091 to 094.

Procedure

1. Enter Diagnostics, GP 1.
2. Touch dC330 Component Control.

CAUTION: Check the component control tables for components that will damage the machine if run together.

3. Touch Chain-Link.
4. Enter the relevant Chain-Link number.
5. Touch OK.
6. Touch Start. The component will operate and the screen will display the information that follows:

• Chain-Link number of the component.
• Input or output code clarification.
• The component status.
• Operation counter.

7. Toggle Cyclic Motion to repeat the operation.
8. Touch Stop All to stop component operation.
9. Touch Close to return to the Diagnostics screen.
10. Exit diagnostics, GP 1.

Input Codes

Table 1 Input codes 005
Code Displayed Name Description General
005-102 Document Sensor Document sensor (Q05-102) High = document present
005-110 Regi Sensor Registration sensor (Q05-110) High = no document
005-206 CVT Pre Regi Sensor Pre-registration sensor (Q05-206) High = no document
005-211 CVT Invert Sensor Invert sensor (Q05-211) High = no document
005-212 CVT Feeder Cover Interlock Switch CVT feeder cover sensor (Q05-212) High = Cover closed
005-213 CVT DADF Interlock Switch CVT DADF interlock switch (S05-213) High = DADF lowered
005-215 CVT #1 Tray APS Sensor (CVT) Tray APS sensor 1 (Q05-215) High/Low
005-216 CVT #2 Tray APS Sensor (CVT) Tray APS sensor 2 (Q05-216) High/Low
005-217 CVT #3 Tray APS Sensor (CVT) Tray APS sensor 3 (Q05-217) High/Low
005-218 CVT APS No. 1 Sensor APS sensor 1 (Q05-218) Low = document present
005-219 CVT APS No. 2 Sensor APS sensor 2 (Q05-219) Low = document present
005-220 CVT APS No. 3 Sensor APS sensor 3 (Q05-220) Low = document present
005-221 CVT Tray Size SNR No. 1 Tray size sensor 1 (Q05-221) Low = document present
005-222 CVT Tray Size SNR No. 2 Tray size sensor 2 (Q05-222) Low = document present
005-224 Scan Start (CVT) Scan count signal. High = on
005-226 #2 Invert Sensor (PF1) Invert sensor 2 (Q05-226) Low = document present
005-234 Home Position SNR Link home position sensor (Q05-234) for nip release High = nip

Table 2 Input Codes 012 - Integrated Office Finisher
Code Displayed Name Description General
012-111 IOT Exit Sensor IOT exit sensor (Q12-111) High/Low
012-140 Ent Sensor Entry sensor (Q12-140) High/Low
012-150 Compile Exit Sensor Compiler exit sensor (Q12-150) High/Low
012-220 Front Tamper Home Sensor Front tamper home sensor (Q12-220) High = home
012-221 Rear Tamper Home Sensor Rear tamper home sensor (Q12-221) High = home
012-242 Low Staple Sensor Low staples sensor (Q12-242) High = almost empty
012-243 Self Priming Sensor Self priming sensor (Q12-243) High = ready
012-244 Staple Home Sensor Staple head home sensor (Q12-244) High = staple head home
012-251 Set Clamp Home Sensor Set clamp home sensor (Q12-251) High = set clamp home
012-252 Eject Home Sensor Ejector home sensor (Q12-252) High = Ejector home
012-267 Stack Height Sensor Stack height sensor (Q12-267) High/Low
012-278 Stack Sensor1 Stack sensor 1 (Q12-278) High/Low
012-279 Stack Sensor2 Stack sensor 2 (Q12-279) High/Low
012-300 Top Cover Interlock Top cover interlock switch (S12-302) High/Low
012-302 Finisher Front Door SW Font door interlock switch (S12-302) High/Low

Table 3 Input Codes 012 and 013 - Office Finisher LX
Code Displayed Name Description General
012-100 Transport Entrance Sensor Transport entry sensor (Q12-100) High/Low
012-110 Reg. Clutch on Detect Registration clutch (CL12-110) On/off
012-111 IOT Exit Sensor IOT exit sensor (Q12-111) High/Low
012-150 Compile Exit Sensor Compiler exit sensor (Q12-150) High/Low
012-151 Compiler Tray No Paper Sensor Compiler tray no paper sensor (Q12-151) High/Low
012-190 H-Transport Entrance Sensor H-transport entrance sensor (Q12-190) High/Low
012-220 Front Tamper Home Sensor Front tamper home sensor (Q12-220) High = home
012-221 Rear Tamper Home Sensor Rear tamper home sensor (Q12-221) High = home
012-241 Stapler Move Position Sensor Stapler move position sensor (Q12-241) High/Low
012-242 Low Staple Sensor Low staples sensor (Q12-242) High = almost empty
012-243 Self Priming Sensor Self priming sensor (Q12-243) High = ready
012-244 Staple Home Sensor Staple head home sensor (Q12-244) High = staple head home
012-250 Eject Clamp Home Sensor Eject clamp home sensor (Q12-250) High/Low
012-251 Set Clamp Home Sensor Set clamp home sensor (Q12-251) High = set clamp home
012-260 Upper Limit Sensor Upper limit sensor (Q12-260) High/Low
012-262 Stacker Paper Sensor Stacker paper sensor (Q12-262) High/Low
012-263 Stacker Encoder Sensor Stacker encoder sensor (Q12-263) High/Low
012-264 Stack Height Sensor 1 Stack height sensor 1 (Q12-264) High/Low
012-265 Stack Height Sensor 2 Stack height sensor 2 (Q12-265) High/Low
012-271 Punch Home Sensor Punch home sensor (Q12-271) High/Low
012-274 Punch Encoder Sensor Punch encoder sensor (Q12-274) High/Low
012-275 Punch Box Set Sensor Punch box set sensor (Q12-275) High/Low
012-277 Puncher Detect Puncher detect (Q12-277) High/Low
012-300 Eject Cover Switch Eject cover switch (S12-300) High/Low
012-302 Fin. Front Door Intlk Switch Finisher front door interlock switch (S12-302) High/Low
012-303 H-Transport Open Sensor H-transport open sensor (Q12-303) High/Low
013-101 Folder Home Sensor Folder home sensor (Q13-101) High/Low
013-107 Booklet Front Low Staple Switch Booklet front low staple switch (S13-107) High = Staple slow
013-108 Booklet Rear Low Staple Switch Booklet rear low staple switch (S13-108) High = Staple slow
013-141 Booklet Front Staple Home Switch Booklet front staple home switch (S13-141) High/Low
013-142 Booklet Rear Staple Home Switch Booklet rear staple home switch (S12-142) High/Low
013-143 Booklet Stapler Move Position Sensor Booklet stapler move position sensor (S13-143) High/Low
013-144 Booklet Stapler Move Home Sensor Booklet stapler move home sensor (S13-144) High/Low
013-160 Folder Detect Folder detect High/Low
013-161 Booklet Detect Booklet detect High/Low
013-300 Booklet Cover Open Switch Booklet cover open switch (S13-300) High/Low
013-301 Booklet Safety Switch Booklet safety switches High/Low

Table 4 Input codes 042
Code Displayed Name Description General
042-200 YMC Link Sensor YMC link sensor (Q42-200) High/Low
042-250 Fusing Exhaust Fan Fail Detects using exhaust fan fail. -
042-251 Marking Fan FAIL Detects marking fan fail. -

Table 5 Input codes 062
Code Displayed Name Description General
062-212 IIT Regi Sensor Scanner registration sensor (Q62-212) Low = Actuated
062-240 ADF Exist DADF present sensor (Q62-240) High = DADF present
062-251 APS Sensor1 APS sensor 1 (Q62-251) High = document present
062-253 APS Sensor3 APS sensor 3(Q62-253) High = document present
062-300 Platen I/L Switch Platen I/L sensor (Q62-300) Low = DADF closed
062-301 Angle Sensor Angle sensor (Q62-301) Low = DADF closed

Table 6 Input codes 071 to 078
Code Displayed Name Description General
071-101 #1 No Paper Sensor Tray 1 no paper sensor (Q71-101) High = Paper empty
071-102 #1 Level Sensor Tray 1 level sensor (Q71-102) High = top of stack sensed
071-104 #1 Tray Paper Size Switch Tray 1 paper size switch (S71-104) High = Tray out
071-105 #1 Pre Feed Sensor Tray 1 pre feed sensor (Q71-105) High = paper detected
072-101 #2 No Paper Sensor Tray 2 no paper sensor (Q72-101) High = Paper empty
072-102 #2 Level Sensor Tray 2 level sensor (Q72-102) High = top of stack sensed
072-103 #2 Feed Out Sensor Tray 2 feed out sensor (Q72-103) High = Paper Detected
072-104 #2 Tray Paper Size Sensor Digital Tray 2 paper size sensor (Q72-104) -
073-101 #3 No Paper Sensor Tray 3 no paper sensor (Q73-101) High = Paper empty
073-102 #3 Level Sensor Tray 3 level sensor (Q73-102) High = top of stack sensed
073-103 #3 Feed Out Sensor Tray 3 feed out sensor (Q73-103) High = Paper Detected
073-104 #3 Tray Paper Size Sensor Digital Tray 3 paper size sensor (Q73-104) -
074-101 #4 No Paper Sensor Tray 4 no paper sensor (Q74-101) High = Paper empty
074-102 #4 Level Sensor Tray 4 level sensor (Q74-102) High = top of stack sensed
074-103 #4 Feed Out Sensor Tray 4 feed out sensor (Q74-103) High = Paper Detected
074-104 #4 Tray Paper Size Sensor Digital Tray 4 paper size sensor (Q74-104) High/Low
075-100 MSI No Paper Sensor Bypass tray no paper sensor (Q75-100) High = Paper detected
077-100 #2 Exit Sensor Exit 2 sensor (Q77-100) High = paper detected
077-101 #1 Exit Sensor Exit 1 sensor (Q77-101) High = paper detected
077-104 Regi Sensor Registration sensor (Q77-104) High = paper detected
077-105 #2 Feed Out Sensor #2 Feed Out Sensor High = paper detected
077-120 IOT Feed Ready Signal Input Feed ready signal On/off
077-121 Tray Module Regi Stop Signal Input Registration stop signal. On/off
077-123 Tray Module Feed ON Signal Input Feed on signal. On/off
077-124 #1 OCT Full Stack Sensor Exit 1 OCT full stack sensor (Q77-124) High/Low
077-300 Left Hand Interlock Switch Left hand interlock switch (S77-300) High/Low
077-302 Left Hand High Cover Switch Left hand high cover switch (S77-302) High/Low
077-303 Front Interlock Switch Front interlock switch (S77-303) High/Low
077-306 Tray Module Left Hand Interlock Switch TM left hand interlock switch (S77-306) High = cover closed
078-100 HCF1 Pre Feed Sensor HCF pre feed sensor (Q78-100) High/Low
078-101 HCF1 Feed Out Sensor HCF feed out sensor (Q78-101) High/Low
078-200 HCF1 No Paper Sensor HCF no paper sensor (Q78-200) High/Low
078-201 HCF1 Level Sensor HCF level sensor (Q78-201) High/Low
078-202 HCF1 Size Sensor A HCF size sensor A (Q78-202) High/Low
078-203 HCF1 Size Sensor B HCF size sensor B (Q78-203) High/Low
078-204 HCF1 Tray In Sensor HCF tray in sensor (Q78-204) High/Low
078-300 HCF1 Transport Interlock HCF transport interlock(S78-300) High/Low
078-301 HCF1 Side Out Switch HCF side out switch (S78-301) High/Low

Table 7 Input codes 091
Code Displayed Name Description General
091-200 Waste Toner Full Sensor Detects toner waste bottle near full. -


Output Codes

Table 8 Output Codes 005
Code Displayed Name Description General
005-004 Feed Motor (CCW) 82.5mm/s Runs the DADF feed motor (MOT05-004) counter clockwise at 82.5mm/s. 50 seconds timeout. On/off
005-005 Feed Motor (CCW) 110.0mm/s Runs the DADF feed motor (MOT05-004) counter clockwise at 110mm/s. 50 seconds timeout. On/off
005-008 Feed Motor (CCW) 165.0mm/s Runs the DADF feed motor (MOT05-004) counter clockwise at 165mm/s. 50 seconds timeout. On/off
005-009 Feed Motor (CW) 330.0mm/s Runs the DADF feed motor (MOT05-004) clockwise at 330mm/s. 50 second timeout. On/off
005-010 Feed Motor (CCW) 220.0mm/s Runs the DADF feed motor (MOT05-004) counter clockwise at 220mm/s. 50 second timeout. On/off
005-013 Feed Motor (CW) 440.0mm/s Runs the DADF feed motor (MOT05-004) clockwise at 440mm/s. 50 second timeout. On/off
005-015 Feed Motor (CCW) 330.0mm/s Runs the DADF feed motor (MOT05-004) counter clockwise at 330mm/s. 50 second timeout. On/off
005-047 Feed Motor (CW) 110.0mm/s Runs the DADF feed motor (MOT05-004) clockwise at 110mm/s. 50 second timeout. On/off
005-048 Feed Motor (CW) 165.0mm/s Runs the DADF feed motor (MOT05-004) clockwise at 165mm/s. 50 second timeout. On/off
005-049 Feed Motor (CW) 220.0mm/s Runs the DADF feed motor (MOT05-004) clockwise at 220mm/s. 50 second timeout. On/off
005-062 DADF Feed Clutch Energises the DADF feed clutch (CL05-062). 50 second timeout. On/off
005-072 Nip Release Solenoid Nip release solenoid (SOL05-072). 3 second timeout. On/off
005-083 Doc Ready Switches on the document ready signal. On/off
005-088 Image Area Image area. On/off
005-098 Takeaway Clutch Energises the DADF takeaway clutch (CL05-098). 50 second timeout. On/off

Table 9 Output Codes 012 - Integrated Office Finisher
Code Displayed Name Description General
012-013 Sub Paddle Solenoid Energizes the sub paddle solenoid (SOL12-013).

CAUTION: Do not run with 012-014. Running these codes at the same time can cause damage to the machine.
On/off. 660ms timeout.
012-014 Sub Paddle Rotation Simultaneously runs the transport motor (MOT12-095) and energizes the paddle solenoid (SOL12-013) to rotate the sub paddle once.

CAUTION: Do not run with 012-013, 012-095, 012-096 or 012-097. Running these codes at the same time can cause damage to the machine.
On/off. 660ms timeout.
012-017 Set Clamp Motor Runs the set clamp motor (MOT12-017).

CAUTION: Do not run with 012-061. Running these codes at the same time can cause damage to the machine.
On/off. 250 pulses.
012-020 Front Tamper Mot Low Front Runs the front tamper motor (MOT12-020) at low speed to move the front tamper forward. On/off. 100 pulses.
012-021 Front Tamper Mot Middle Front Runs the front tamper motor (MOT12-020) at mid speed to move the front tamper forward. On/off. 100 pulses
012-022 Front Tamper Mot High Front Runs the front tamper motor (MOT12-020) at high speed to move the front tamper forward. On/off. 100 pulses
012-023 Front Tamper Mot Low Rear Runs the front tamper motor (MOT12-020) at low speed to move the front tamper backward. On/off. 100 pulses
012-024 Front Tamper Mot Middle Rear Runs the front tamper motor (MOT12-020) at mid speed to move the front tamper backward. On/off. 100 pulses
012-025 Front Tamper Mot High Rear Runs the front tamper motor (MOT12-020) at high speed to move the front tamper backward. On/off. 100 pulses
012-026 Rear Tamper Mot Low Front Runs the rear tamper motor (MOT12-026) at low speed to move the rear tamper forward. On/off. 100 pulses.
012-027 Rear Tamper Mot Middle Front Runs the rear tamper motor (MOT12-026) at mid speed to move the rear tamper forward. On/off. 100 pulses
012-028 Rear Tamper Mot High Front Runs the rear tamper motor (MOT12-026) at high speed to move the rear tamper forward. On/off. 100 pulses
012-029 Rear Tamper Mot Low Rear Runs the rear tamper motor (MOT12-026) at low speed to move the rear tamper backward. On/off. 100 pulses.
012-030 Rear Tamper Mot Middle Rear Runs the rear tamper motor (MOT12-026) at mid speed to move the rear tamper backward. On/off. 100 pulses
012-031 Rear Tamper Mot High Rear Runs the rear tamper motor (MOT12-026) at high speed to move the rear tamper backward. On/off. 100 pulses
012-046 Staple Motor FORWARD Runs the staple motor (MOT12-046) forwards. On/off.
012-047 Staple Motor REVERSE Runs the staple motor (MOT12-046) in reverse. On/off. 180ms timeout.
012-054 Eject Motor Low FORWARD Runs the eject motor (MOT12-054) at low speed to move the ejector out. On/off. 2000 pulses
012-055 Eject Motor High FORWARD Runs the eject motor (MOT12-054) at high speed to move the ejector out. On/off. 2000 pulses
012-056 Eject Motor Low REVERSE Runs the eject motor (MOT12-054) at low speed to move the ejector home. On/off. 2000 pulses
012-057 Eject Motor High REVERSE Runs the eject motor (MOT12-054) at high speed to move the ejector home. On/off. 2000 pulses
012-060 Stacker Motor UP Runs the stacker motor (MOT12-060) to drive the stacker tray up. On/Off. 80ms timeout.
012-061 Stacker Motor DOWN Runs the stacker motor (MOT12-060) to drive the stacker tray down. On/Off. 80ms timeout.
012-095 Transport Motor Low Runs the transport motor (MOT12-095) forward at low speed (equal to full IOT speed).
012-096 Transport Motor Hi Runs the transport motor (MOT12-095) forward at high speed (transport speed in finisher).
012-097 Transport Motor Half Speed Runs the transport motor (MOT12-095) forward at half speed (equal to half IOT speed).
012-110 Registration Clutch ON Energizes the registration clutch (CL12-110).

Table 10 Output Codes 012 and 013 - Office Finisher LX
Code Displayed Name Description General
012-013 Sub Paddle Solenoid Energizes the sub paddle solenoid (SOL12-013). On/off. 250 ms
012-018 Transport Motor Reverse Runs the transport motor (MOT12-018) in reverse. On/off.
012-020 Front Tamper Mot Low Front Runs the front tamper motor (MOT12-020) at low speed to move the front tamper forward. On/off. 82 pulses
012-022 Front Tamper Mot High Front Runs the front tamper motor (MOT12-020) at high speed to move the front tamper forward. On/off. 82 pulses
012-023 Front Tamper Mot Low Rear Runs the front tamper motor (MOT12-020) at low speed to move the front tamper backward. On/off. 82 pulses
012-025 Front Tamper Mot High Rear Runs the front tamper motor (MOT12-020) at high speed to move the front tamper backward. On/off. 82 pulses
012-026 Rear Tamper Motor Low Front Runs the rear tamper motor (MOT12-026) at low speed to move the rear tamper forward. On/off. 82 pulses
012-028 Rear Tamper Motor High Front Runs the rear tamper motor (MOT12-026) at high speed to move the front tamper forward. On/off. 82 pulses
012-029 Rear Tamper Motor Low Rear Runs the rear tamper motor (MOT12-026) at low speed to move the rear tamper backward. On/off. 82 pulses
012-031 Rear Tamper Motor High Rear Runs the rear tamper motor (MOT12-026) at high speed to move the rear tamper backward. On/off. 82 pulses
012-032 H-Transport Motor 1 Runs the horizontal transport motor (MOT12-032) forward at highest speed. On/off.
012-033 H-Transport Motor 2 Runs the horizontal transport motor (MOT12-032) forward at high speed. On/off.
012-034 H-Transport Motor 3 Runs the horizontal transport motor (MOT12-032) forward at mid speed. On/off.
012-035 H-Transport Motor 4 Runs the horizontal transport motor (MOT12-032) forward at low speed. On/off.
012-036 Transport Motor 1 Runs the transport motor (MOT12-036) forward at high speed. On/off.
012-037 Transport Motor 2 Runs the transport motor (MOT12-036) forward at mid speed. On/off.
012-038 Transport Motor 3 Runs the transport motor (MOT12-036) forward at low speed. On/off.
012-039 H-Transport Motor Reverse Runs the horizontal transport motor (MOT12-032) in reverse. On/off.
012-040 Stapler Move Motor Front Low Runs the stapler move motor (MOT12-040) to move the stapler assembly to the front at low speed. On/off.
012-042 Stapler Move Motor Front High Runs the stapler move motor (MOT12-040) to move the stapler assembly to the front at high speed. On/off.
012-043 Stapler Move Motor Rear Low Runs the stapler move motor (MOT12-040) to move the stapler assembly to the rear at low speed. On/off.
012-045 Stapler Move Motor Rear High Runs the stapler move motor (MOT12-040) to move the stapler assembly to the rear at high speed. On/off.
012-046 Staple Motor Forward Runs the stapler motor (MOT12-046) forwards. On/off.
012-047 Staple Motor Reverse Runs the stapler motor (MOT12-046) in reverse. On/off. 200ms timeout.
012-050 Set Clamp Clutch Energizes the set clamp clutch (CL12-050). On/off. 583 pulses.
012-052 Eject Clamp Up Runs the eject motor (MOT12-054) in reverse at high speed to raise the eject clamp roll. On/off. 200ms timeout.
012-053 Eject Clamp Down Runs the eject motor (MOT12-054) in reverse at high speed to lower the eject clamp roll. On/off. 46 pulses after home.
012-054 Eject Motor Forward Low Runs the eject motor (12-054) forward at low speed. On/off. 1136 pulses.
012-055 Eject Motor Forward High Runs the eject motor (12-054) forward at high speed. On/off. 1136 pulses.
012-060 Stacker Motor Up Runs the stacker motor (MOT12-060) to drive the stacker tray up. On/Off. 500ms timeout.
012-061 Stacker Motor Down Runs the stacker motor (MOT12-060) to drive the stacker tray down. On/Off. 500ms timeout.
012-074 Punch Motor Move Home Runs the punch motor (MOT12-074) to drive the punch home. On/off.
012-077 Punch (2 hole) Runs the punch motor (MOT12-074) to drive 2 hole punch movement. On/off.
012-078 Punch (3 hole) Runs the punch motor (MOT12-074) to drive 3 hole punch movement. On/off.
012-079 Punch (4 hole) Runs the punch motor (MOT12-074) to drive 4 hole punch movement. On/off.
013-022 Knife Motor Forward Runs the knife motor (MOT13-022) forward. On/off.
013-023 Knife Motor Reverse Runs the knife motor (MOT13-022) in reverse. On/off.
013-024 Booklet Front Stapler Motor Forward Runs the front booklet staple motor (MOT13-024) forward. On/off.
013-025 Booklet Front Stapler Motor Reverse Runs the front booklet staple motor (MOT13-024) in reverse. On/off.
013-026 Booklet Rear Stapler Motor Forward Runs the rear booklet staple motor (MOT13-026) forward. On/off.
013-027 Booklet Front Stapler Motor Reverse Runs the rear booklet staple motor (MOT13-026) in reverse. On/off.
013-028 Booklet Staple Move Motor In Runs the booklet staple move motor (MOT13-028) to move booklet stapler to the I/B side. On/off. 350 pulses
013-029 Booklet Staple Move Motor Out Runs the booklet staple move motor (MOT13-028) to move booklet stapler to the O/B side. On/off. 350 pulses

Table 11 Output Codes 042
Code Displayed Name Description General
041-001 AllSub integrated mode Drum, dispense, waste toner box auger and fuser exit 1 noise detection processing. -
041-002 Drum abnormal sound detection mode Drum abnormal sound detection processing. -
041-003 Dispense noise detection mode Dispense abnormal sound detection processing. -
041-004 Waste toner box auger and fuser exit 1 noise detection mode Waste toner box auger and fuser exit 1 noise detection processing. -
042-001 Main Motor (175mm/s) Runs the main motor (MOT42-001) at 175mm/s. On/off
042-002 Main Motor (126mm/s) Runs the main motor (MOT42-001) at 126mm/s. On/off
042-003 Main Motor (63mm/s) Runs the main motor (MOT42-001) at 63mm/s. On/off
042-004 Sub Motor (175mm/s) Runs the sub motor (MOT42-004) at 175mm/s. On/off
042-005 Sub Motor (126mm/s) Runs the sub motor (MOT42-004) at 126mm/s. On/off
042-006 Sub Motor (63mm/s) Runs the sub motor (MOT42-004) at 63mm/s. On/off
042-007 Fusing Motor (175mm/s) Runs the fusing motor (MOT42-007) at 175mm/s. On/off
042-008 Fusing Motor (126mm/s) Runs the fusing motor (MOT42-007) at 126mm/s. On/off
042-009 Fusing Motor (63mm/s) Runs the fusing unit drive motor (MOT42-007) at 63mm/s. On/off
042-010 YMC Link Solenoid Energizes the YMC link solenoid (SOL42-010) On/off
042-011 1st BTR Initialize Initialize the 1st BTR. On/off
042-050 Fusing Unit Exhaust Fan High Speed Rotation Runs the fuser exhaust fan (MOT42-050) at high speed. On/off
042-051 Fusing Unit Exhaust Fan Low Speed Rotation Runs the fuser exhaust fan (MOT42-050) at low speed. On/off
042-052 Marking Fan High Speed Rotation Runs the marking fan (MOT42-052) at high speed. On/off
042-053 Marking Fan Low Speed Rotation Runs the marking fan (MOT42-052) at low speed. On/off

Table 12 Output Codes 061 and 062
Code Displayed Name Description General
061-001 LPH forced ON (allsolid) Switches on the print head assembly (all beta pattern). On/off
061-002 LPH forced ON (Cin 50%) Switches on the print head assembly (Cin 50%). On/off
061-003 LPH forced ON (thyristor transfer) Switches on the print head assembly (performs thyristor transfer only). On/off
062-002 IIT Exposure Lamp Switches on the exposure Lamp. 3 minute timeout. On/off
062-005 IIT Scan Motor (Scan direction) Runs the scan motor (MOT62-005) to drive the scan carriage 50mm (2 inches) in the scan direction. -
062-006 IIT Scan Motor (Return direction) Runs the scan motor (MOT62-005) to drive the scan carriage 50mm (2 inches) in the return direction. -

Table 13 Output Codes 071 to 078
Code Displayed Name Description General
071-001 #1 Feed Motor 1-2-phase Feed Direction Runs the tray 1 feed/lift motor (MOT71-001) at paper feed speed in the feed direction. On/off
071-002 #1 Feed Motor 2-phase Lift Up Direction Runs the tray 1 feed/lift motor (MOT71-001) at tray lift speed in the lift direction. On/off
072-001 #2 Feed Motor 2-phase (CW 2) Feed Direction Runs the tray 2 feed/lift motor (MOT72-001) at paper feed speed in the feed direction (2 phase control). On/off
072-002 #2 Feed Motor 2-phase (CCW 2) Lift Up Direction Runs the tray 2 feed/lift motor (MOT72-001) at tray lift speed in the lift direction. On/off
072-003 #2 Feed Motor 1-2-phase (CW 1-2) Feed Direction Runs the tray 2 feed/lift motor (MOT72-001) at paper feed speed in the feed direction (1-2 phase control) On/off
073-001 #3 Feed Motor 2-phase (CW 2) Feed Direction Runs the tray 3 feed/lift motor (MOT73-001) at paper feed speed in the feed direction (2 phase control). On/off
073-002 #3 Feed Motor 2-phase (CCW 2) Lift Up Direction Runs the tray 3 feed/lift motor (MOT73-001) at paper feed speed in the feed direction (1-2 phase control) On/off
073-003 #3 Feed Motor 1-2-phase (CW 1-2) Feed Direction Runs the tray 3 feed/lift motor (MOT73-001) (1-2 phase control) On/off
074-001 #4 Feed Motor 2-phase (CW 2) Feed Direction Runs the tray 4 feed/lift motor (MOT74-001) at paper feed speed in the feed direction (2 phase control). On/off
074-002 #4 Feed Motor 2-phase (CCW 2) Lift Up Direction Runs the tray 4 feed/lift motor (MOT74-001) at tray lift speed in the lift direction. On/off
074-003 #4 Feed Motor 1-2-phase (CW 1-2) Feed Direction Runs the tray 4 feed/lift motor (MOT74 -001) at paper feed speed in the feed direction (1-2 phase control) On/off
075-001 MSI Feed Clutch Energizes the bypass tray feed clutch (CL75-001). On/off
077-001 Takeaway Clutch Energizes the takeaway clutch (CL077-001). On/off
077-002 Regi Clutch Energizes the registration clutch (CL77-002). On/off
077-003 Duplex Clutch Energizes the duplex clutch (CL77-003). On/off
077-004 Exit Gate Solenoid Energizes the exit gate solenoid (SOL77-004). On/off
077-010 #1 Exit Offset Solenoid Energizes the exit 1 offset solenoid (SOL77-010). On/off
077-014 Exit 2 Drive Motor Forward Rotation Runs the exit 2 drive motor (MOT77-014) forwards (output direction). On/off
077-015 Exit 2 Drive Motor Reverse Rotation Runs the exit 2 drive motor (MOT77-014) in reverse (intake direction). On/off
077-030 TM Feed Ready Signal Output Switches on the feed ready signal. On/off
077-031 IOT Regi Stop Signal Output Switches on the registration stop signal. On/off
077-032 IOT Feed ON Signal Output Switches on the feed on signal. On/off
077-033 TM T/A Motor 1 Full Speed Runs the TM T/A motor 1 (MOT77-033) at full speed. On/off
077-034 TM T/A Motor 1 Half Speed Runs the TM T/A motor 1 (MOT77-033) at half speed. On/off
077-035 TM T/A Motor 2 Full Speed Runs the TM T/A motor 2 (MOT77-035) at full speed. On/off
077-036 TM T/A Motor 2 Half Speed Runs the TM T/A motor 2 (MOT77-035) at half speed. On/off
078-003 HCF1 Feed Motor -Feed Direction Runs the HCF feed/lift motor (MOT78-003) in the feed direction. On/off
078-004 HCF1 Feed Motor – Lift Up Runs the HCF feed/lift motor (MOT78-003) in the lift direction. On/off
078-093 HCF1 T/A Motor Runs the HCF T/A motor (MOT78-093) at low speed. On/off
078-094 HCF1 T/A Motor Runs the HCF T/A motor (MOT78-093) at high speed. On/off

Table 14 Output Codes 091 to 094
Code Displayed Name Description General
091-001 BCR Y DC Energizes the BCR DC Y bias voltage. On/off
091-002 BCR M DC Energizes the BCR DC M bias voltage. On/off
091-003 BCR C DC Energizes the BCR DC C bias voltage. On/off
091-004 BCR K DC Energizes the BCR DC K bias voltage. On/off
092-001 R_RAD_COM_DA Switches on or off the R-RAD LED. On/off
092-002 ADC shutter open Energizes the CTD shutter solenoid to open the ADC shutter. 150ms timeout.
092-003 ADC shutter Close De-energizes the CTD shutter solenoid to close the ADC shutter. 150ms timeout.
093-001 DISPENSE MOTOR-Y Runs the Y dispense motor (MOT93-001) at process speed. On/off
093-002 DISPENSE MOTOR-M Runs the M dispense motor (MOT93-002) at process speed. On/off
093-003 DISPENSE MOTOR-C Runs the C dispense motor (MOT93-003) at process speed. On/off
093-004 DISPENSE MOTOR-K Runs the K dispense motor (MOT93-004) at process speed. On/off
093-005 DEVE BIAS-DC-YMC Energizes the Dev. DC YMC bias voltage. On/off
093-006 DEVE BIAS-DC-K Energizes the Dev. DC K bias voltage. On/off
093-007 DEVE BIAS-AC-YMC Energizes the Dev. AC YMC bias voltage. On/off
093-008 DEVE BIAS-AC-K Energizes the Dev. AC K bias voltage. On/off
093-009 DEVE CLUTCH-K Energizes the developer clutch K. On/Off. 2000ms timeout.
094-001 2nd BTR (-) Energizes the 2nd BTR (-) bias. On/off
094-002 2nd BTR (+) Energizes the 2nd BTR (+) bias. On/off
094-003 1st BTR YMC Contact Brings the 1st BTR (YMC) into contact with the drum. -
094-004 1st BTR YMC Retract Retracts the 1st BTR (YMC) from the drum. -


**This procedure is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**

You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.

Toner Chip (For North America and West Europe Region):

106R03741 106R03744 106R03743 106R03742
106R03757 106R03760 106R03759 106R03758
106R03737 106R03740 106R03739 106R03738

Toner Chip (For South America and East Europe Region):

106R03749 106R03752 106R03751 106R03750
106R03745 106R03748 106R03747 106R03746
106R03765 106R03768 106R03767 106R03766

Toner Chip (For Metered Machine):

106R03733 106R03736 106R03735 106R03734

Drum Chip:

113R00780 113R00782

Share this post



← Older Post Newer Post →


Leave a comment