How to Fix 010-329 Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
010-329 Fuser Fuse Cut Fail RAP
BSD-ON: BSD 10.2 Fusing Heat Control (1 of 2)
010-329 After installation of a new fuser, the fuse (F1) for detection is not open within the correct time.
Procedure
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
Perform the steps that follow:
1. Switch off, then switch on the machine, GP 10.
2. Ensure that the fuser is installed correctly.
3. Check the drawer connector between the fuser and the main unit (DP612) for damage.
4. Check the connections and wiring between the fuser fuse PWB (P/J567) and the drive PWB (P/J416 for an open circuit, short circuit or poor contact.
5. Check the connection between the fuser (DP612) and the drive PWB (P/J416) for an open circuit, short circuit or poor contact.
6. If the fault persists, install new components as necessary:
• Fuser, PL 10.05 Item 2.
• Drive PWB, PL 1.10 Item 4.
• ESS PWB, PL 3.10 Item 6.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON: BSD 10.2 Fusing Heat Control (1 of 2)
010-329 After installation of a new fuser, the fuse (F1) for detection is not open within the correct time.
Procedure
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
Perform the steps that follow:
1. Switch off, then switch on the machine, GP 10.
2. Ensure that the fuser is installed correctly.
3. Check the drawer connector between the fuser and the main unit (DP612) for damage.
4. Check the connections and wiring between the fuser fuse PWB (P/J567) and the drive PWB (P/J416 for an open circuit, short circuit or poor contact.
5. Check the connection between the fuser (DP612) and the drive PWB (P/J416) for an open circuit, short circuit or poor contact.
6. If the fault persists, install new components as necessary:
• Fuser, PL 10.05 Item 2.
• Drive PWB, PL 1.10 Item 4.
• ESS PWB, PL 3.10 Item 6.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782