How to Enter GP 22 Special Boot Modes for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?

Posted by Xwk Tech on

Purpose

To start the device in various modes to enable special functions.

Procedure

1. Switch off the machine, GP 10.
2. Simultaneously press then hold down the Home and Power buttons until the device powers on and SPECIAL BOOT MENU appears.
3. Simultaneously touch the letters A in SPECIAL, B in BOOT and the Home button. Do not hold any of the three locations, just touch/press then release simultaneously.
4. At the keypad screen enter code number, 6789#. The first SPECIAL BOOT MENU screen will display.

CAUTION: Do not switch off the device until the reboot is complete. The device will reboot after the download is complete.

5. Scroll through the SPECIAL BOOT MENU screens to select the appropriate function, refer to Table 1. Follow the on screen instructions. The device may reboot, then print a report.

Table 1 Next level of menu
Function Display Notes
DOWNLOAD MODE --BOOT MODE--
DOWNLOAD MODE
ARE YOU SURE?
YES
NO
Machine starts in Firmware Download Mode. Refer to GP 4.
LONGDIAG MODE --BOOT MODE--
LONGDIAG MODE
ARE YOU SURE?
YES
NO
Performs a more detailed check than the usual device diagnostic items at machine start. If a fault code is displayed, perform the relevant procedure.
01. JOB LOG CLEAR MODE --BOOT MODE--
01. JOB LOG CLEAR MODE
ARE YOU SURE?
YES
NO
Used to clear corrupted jobs.
02. FACTORY INIT MODE --BOOT MODE--
02. FACTORY INIT MODE
ARE YOU SURE?
YES
NO
CAUTION: Do not perform this mode unless directed.

Machine will be reset and the message NVMEM IS CLEARED will be displayed. Switch the machine off, then on, GP 10. Fault code 116-334 will be displayed, again switch the machine off, then on, GP 10. Fault code 124-315 will be displayed, perform dC132. The machine will restart at the install
wizard.

CAUTION: All customer configured settings will be deleted. To restore the customer configured settings, a clone file is required. Refer to GP 13.

NOTE: The install dongle will not be required.
03. NVRAM INIT MODE -BOOT MODE--
03. NVRAM INIT MODE
ARE YOU SURE?
YES
NO
Forcibly initializes the controller NVM back to default. This is the same as initializing the Sys - System NVM and Sys - User NVM in dC301.
04. HDD FORMAT MODE -BOOT MODE--
04. HDD FORMAT MODE
ARE YOU SURE?
YES
NO
All pending jobs will be deleted. The HDD will be forcibly reformatted.

CAUTION: All customer data on the HDD (mailboxes, scanned documents, user IDs and account IDs) will be deleted.
06. HDD INITIALIZE MODE --BOOT MODE--
06. HDD INITIALIZE MODE
ARE YOU SURE?
YES
NO
All pending jobs will be deleted. The spool area of the HDD will be initialized.

CAUTION: All customer data on the HDD (mailboxes, scanned documents, user IDs and account IDs) will be deleted.
SKIP INSTALL WIZARD --BOOT MODE--
SKIP INSTALL WIZARD
ARE YOU SURE?
YES
NO
Starts the machine without displaying the install wizard.

**This procedure is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**

You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.

Toner Chip (For North America and West Europe Region):

106R03741 106R03744 106R03743 106R03742
106R03757 106R03760 106R03759 106R03758
106R03737 106R03740 106R03739 106R03738

Toner Chip (For South America and East Europe Region):

106R03749 106R03752 106R03751 106R03750
106R03745 106R03748 106R03747 106R03746
106R03765 106R03768 106R03767 106R03766

Toner Chip (For Metered Machine):

106R03733 106R03736 106R03735 106R03734

Drum Chip:

113R00780 113R00782

Share this post



← Older Post Newer Post →


Leave a comment