Articles

047-320 All Destination Tray Broken RAP047-320 All trays connected to the IOT have become unusable.ProcedureCheck the fault history, dC122 for any tray faults. Perform the relevant procedures.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749 106R03752 106R03751 106R03750• 106R03745 106R03748 106R03747 106R03746• 106R03765 106R03768 106R03767...

047-217 HCF Communication RAPBSD-ON: BSD 3.15 PWB Communications (ESS to HCF)047-217 Reply from the HCF was determined as a communication error.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Switch off, then switch on the machine, GP 10.2. Check the connection between the drive PWB, PL 1.10 Item 3 and the HCF PWB, PL 70.60 Item 9 for open circuit, short circuit or poor contact.3. Install new...

047-213, 047-216 Finisher Communication RAPBSD-ON: BSD 1.7 Option DC Power DistributionBSD-ON: BSD 3.6 PWB Communications (ESS PWB/Drive PWB to Finisher)047-213 The connected finisher is of an incorrect type.047-216 Reply from the finisher was determined as a communication error.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Switch off, then switch on the machine, GP 10.2. Check the connection between the drive PWB ( P/J590 and P/J591) and...

Drive PWB Power Fail RAPBSD-ON: BSD 3.1 PWB Communications (ESS PWB to Drive PWB)BSD-ON: BSD 1.4 DC Power Generation (1 of 2)BSD-ON: BSD 1.5 DC Power Generation (2 of 2)045-399 Power supply to drive PWB error. The IOT_PWR_ON signal from ESS PWB did not become active due to an error. This occurs at ESS circuit error, cable open circuit or no +5V power supply from LVPS.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts...

045-382, 045-398 Drive PWB NVM (EEPROM) Verify Fail RAPBSD-ON: BSD 3.1 PWB Communications (ESS PWB to Drive PWB)045-382 NVM (EEPROM) write verify error.041-398 NVM (EEPROM) read verify error.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Switch off, then switch on the machine, GP 10.2. Reload the software, GP 4.3. Install new components as necessary:• Drive PWB, PL 1.10 Item 3.• ESS PWB, PL 3.10 Item 6.**This...