How to Fix 012-283A 012-284A Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?

Posted by Xwk Tech on


012-283A, 012-284A Set Clamp Home Sensor Fail RAP

BSD-ON: BSD 12.7 Integrated Office Finisher Set Eject (2 of 2)

Initial Actions

NOTE: Ensure the correct RAP is performed, refer to the 012-283, 012-284 Set Clamp Home Sensor Fail Entry RAP.

WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.

• Check the set clamp home sensor, PL 12.11 Item 7 is correctly installed and has no foreign object and that the actuator is not broken.
• Switch off, then switch on the machine, GP 10.

Procedure

1. Check the set clamp mechanism, PL 12.25 for a deformed or broken part and not-seated belts. The mechanism is good. If YES, go to 3. If NO, go to 2.

2. Repair the set clamp mechanism. Install new components as necessary, PL 12.25.

3. Enter dC330 code 012-251. Manually rotate the set clamp shaft to actuate the set clamp home sensor. The display changes. If YES, go to 13. If NO, go to 4.

4. Check the connections of P/J8707, J8742B, J8742A and P/J8723. The connectors are good. If YES, go to 6. If NO, go to 5.

5. Secure the connections.

6. Check for an open or short circuit between P/J8707 and J8742B, and between J8742A and P/J8723. The wiring is good. If YES, go to 8. If NO, go to 7.

7. Repair the open or short circuit.

8. Measure the voltage between the finisher PWB P/J8707 pin 9 (+) and ground (-). The voltage is approximately +5VDC. If YES, go to 10. If NO, go to 9.

9. Check the +5VDC circuit.

10. Measure the voltage between the finisher PWB P/J8707 pin 8 (+) and ground (-). Manually rotate the set clamp shaft to actuate the set clamp home sensor. The voltage changes. If YES, go to 12. If NO, go to 11.

11. Install a new set clamp home sensor, PL 12.11 Item 7.

12. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.

13. Enter dC330 code 012-017. The set clamp motor runs. If YES, go to 21. If NO, go to 14.

14. Check the connections of P/J8708 and P/J8740. The connectors are good. If YES, go to 16. If NO, go to 15.

15. Secure the connections.

16. Check for an open or short circuit between P/J8708 and P/J8740. The wiring is good. If YES, go to 18. If NO, go to 17.

17. Repair the open or short circuit.

18. Measure the voltage between the finisher PWB P/J8708 pin 9 (+) and ground (-), and between P/J8708 pin 11 (+) and ground (-). Each voltage is approximately +24VDC. If YES, go to 20. If NO, go to 19.

19. Check the +24VDC circuit. Refer to Chapter 7 Wiring Data. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.

20. Install a new set clamp motor, PL 12.25 Item 15. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.

21. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.

**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**

You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.

Toner Chip (For North America and West Europe Region):

106R03741 106R03744 106R03743 106R03742
106R03757 106R03760 106R03759 106R03758
106R03737 106R03740 106R03739 106R03738

Toner Chip (For South America and East Europe Region):

106R03749 106R03752 106R03751 106R03750
106R03745 106R03748 106R03747 106R03746
106R03765 106R03768 106R03767 106R03766

Toner Chip (For Metered Machine):

106R03733 106R03736 106R03735 106R03734

Drum Chip:

113R00780 113R00782


Share this post



← Older Post Newer Post →


Leave a comment