How to Fix 012-259 012-280 Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
012-259, 012-280 Eject Home Sensor Fail RAP
BSD-ON: BSD 12.6 Integrated Office Finisher Set Eject (1 of 2)
012-259 The eject home sensor failed to actuate within the specified time.
012-280 The eject home sensor failed to deactuate within the specified time.
Initial Actions
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Check the eject home sensor, PL 12.26 Item 9 is correctly installed, not broken and has no foreign object.
• Switch off, then switch on the machine, GP 10.
Procedure
1. Check the eject mechanism, PL 12.25 for a deformed or broken part and not-seated belts. The mechanism is good. If YES, go to 3. If NO, go to 2.
2. Repair the mechanism. Install new components as necessary, PL 12.25.
3. Enter dC330 code 012-252. Actuate the eject home sensor. The display changes. If YES, go to 13. If NO, go to 4.
4. Check the connections of P/J8700 and P/J8725. The connectors are good. If YES, go to 6. If NO, go to 5.
5. Secure the connections.
6. Check for an open wire or short circuit between P/J8700 and P/J8725. The wiring is good. If YES, go to 8. If NO, go to 7.
7. Repair the open wire or short circuit.
8. Measure the voltage between the finisher PWB P/J8700 pin 9 (+) and ground (-). The voltage is approximately +5VDC. If YES, go to 10. If NO, go to 9.
9. Check the +5VDC circuit.
10. Measure the voltage between the finisher PWB P/J8700 pin 2 (+) and ground (-). Actuate the eject home sensor. The voltage changes. If YES, go to 12. If NO, go to 11.
11. Install a new eject home sensor, PL 12.26 Item 9.
12. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
13. Enter dC330 code 012-054 and 012-056 alternately. The eject motor runs. If YES, go to 21. If NO, go to 14.
14. Check the connections of P/J8706 and P/J8741. The connectors are good. If YES, go to 16. If NO, go to 15.
15. Secure the connections.
16. Check for an open or short circuit between P/J8706 and P/J8741. The wiring is good. If YES, go to 18. If NO, go to 17.
17. Repair the open wire or short circuit.
18. Measure the voltage between the finisher PWB P/J8706 pin 13 (+) and ground (-), and between P/J8706 pin 15 (+) and ground (-). Each voltage is approximately +24VDC. If YES, go to 20. If NO, go to 19.
19. Check the +24VDC circuit. Refer to Chapter 7 Wiring Data. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
20. Install a new eject motor, PL 12.25 Item 15. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
21. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON: BSD 12.6 Integrated Office Finisher Set Eject (1 of 2)
012-259 The eject home sensor failed to actuate within the specified time.
012-280 The eject home sensor failed to deactuate within the specified time.
Initial Actions
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Check the eject home sensor, PL 12.26 Item 9 is correctly installed, not broken and has no foreign object.
• Switch off, then switch on the machine, GP 10.
Procedure
1. Check the eject mechanism, PL 12.25 for a deformed or broken part and not-seated belts. The mechanism is good. If YES, go to 3. If NO, go to 2.
2. Repair the mechanism. Install new components as necessary, PL 12.25.
3. Enter dC330 code 012-252. Actuate the eject home sensor. The display changes. If YES, go to 13. If NO, go to 4.
4. Check the connections of P/J8700 and P/J8725. The connectors are good. If YES, go to 6. If NO, go to 5.
5. Secure the connections.
6. Check for an open wire or short circuit between P/J8700 and P/J8725. The wiring is good. If YES, go to 8. If NO, go to 7.
7. Repair the open wire or short circuit.
8. Measure the voltage between the finisher PWB P/J8700 pin 9 (+) and ground (-). The voltage is approximately +5VDC. If YES, go to 10. If NO, go to 9.
9. Check the +5VDC circuit.
10. Measure the voltage between the finisher PWB P/J8700 pin 2 (+) and ground (-). Actuate the eject home sensor. The voltage changes. If YES, go to 12. If NO, go to 11.
11. Install a new eject home sensor, PL 12.26 Item 9.
12. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
13. Enter dC330 code 012-054 and 012-056 alternately. The eject motor runs. If YES, go to 21. If NO, go to 14.
14. Check the connections of P/J8706 and P/J8741. The connectors are good. If YES, go to 16. If NO, go to 15.
15. Secure the connections.
16. Check for an open or short circuit between P/J8706 and P/J8741. The wiring is good. If YES, go to 18. If NO, go to 17.
17. Repair the open wire or short circuit.
18. Measure the voltage between the finisher PWB P/J8706 pin 13 (+) and ground (-), and between P/J8706 pin 15 (+) and ground (-). Each voltage is approximately +24VDC. If YES, go to 20. If NO, go to 19.
19. Check the +24VDC circuit. Refer to Chapter 7 Wiring Data. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
20. Install a new eject motor, PL 12.25 Item 15. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
21. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782