How to Fix 012-243 012-265 Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?

Posted by Xwk Tech on


012-243, 012-265 Booklet Folder Home Sensor Fail RAP

BSD-ON: BSD 13.8 Office Finisher LX Folding

012-243 Folder home sensor is not actuated after the lapse of 500ms from motor on while folder knife is returning to home.
012-265 When the booklet home moves from home position, the folder home sensor did not turn off within the specified time.

Initial Actions

WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.

• Check the folder home sensor, PL 13.40 Item 16 for improper installation.
• Check the knife drive mechanism, PL 13.40 for a foreign substance.

Procedure

1. Enter dC330 code 013-022 and 013-023 alternately to run the folder knife motor. The fold knife motor runs. If YES, go to 5. If NO, go to 2.

2. Check the wiring between P/J8905 and P/J8990 on the finisher PWB and between P/J8994 on the booklet PWB and J8985 on the finisher PWB for an open or short circuit, or a loose or damaged connector. The wiring is good. If YES, go to 4. If NO, go to 3.

3. Reconnect or repair as necessary.

4. Install a new booklet folder knife motor, PL 13.40 Item 15. If the fault persists, install a new booklet PWB, PL 13.70 Item 4.

5. Enter dC330 code 013-101. Actuate the folder home sensor. The display changes. If YES, go to 13. If NO, go to 6.

6. Check the wiring between J8904 pin 2 and P/J8990 pin 2 on the finisher PWB for an open or short circuit, or a loose or damaged connector. The wiring is good. If YES, go to 8. If NO, go to 7.

7. Reconnect or repair as necessary.

8. Measure the voltage between P/J8990 pins 3 and 1 on the finisher PWB. The voltage is approximately +5VDC. If YES, go to 10. If NO, go to 9.

9. Install a new finisher PWB, PL 13.45 Item 2.

10. Measure the voltage between P/J8990 pin 2 on the finisher PWB and ground. Actuate the folder home sensor. The voltage changes. If YES, go to 12. If NO, go to 11.

11. Install a new folder home sensor, PL 13.40 Item 16.

12. Install a new finisher PWB, PL 13.45 Item 2.

13. If the fault persists, install a new finisher PWB, PL 13.45 Item 2.

**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**

You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.

Toner Chip (For North America and West Europe Region):

106R03741 106R03744 106R03743 106R03742
106R03757 106R03760 106R03759 106R03758
106R03737 106R03740 106R03739 106R03738

Toner Chip (For South America and East Europe Region):

106R03749 106R03752 106R03751 106R03750
106R03745 106R03748 106R03747 106R03746
106R03765 106R03768 106R03767 106R03766

Toner Chip (For Metered Machine):

106R03733 106R03736 106R03735 106R03734

Drum Chip:

113R00780 113R00782


Share this post



← Older Post Newer Post →


Leave a comment