How to Fix 012-161A Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
012-161A Set Eject Jam RAP
BSD-ON: BSD 12.6 Integrated Office Finisher Set Eject (1 of 2)
Initial Actions
NOTE: Ensure the correct RAP is performed, refer to the 012-161 Set Eject Jam Entry RAP
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Check the eject home sensor, PL 12.26 Item 9 is correctly installed, not broken, and has no foreign object.
• Switch off, then switch on the machine, GP 10.
Procedure
1. Check the specification of the paper, GP 15. The paper is in specification. If YES, go to 3. If NO, go to 2.
2. Load paper that is in specification.
3. Check the condition of the paper. The paper is in normal condition without any problem that causes the paper to be bent or caught. If YES, go to 5. If NO, go to 4.
4. Resolve any problem that causes the paper to be bent or caught.
5. Check the eject mechanism, PL 12.25 for deformed parts, broken parts, and/or belt damage. The eject mechanism is good. If YES, go to 7. If NO, go to 6.
6. Repair the eject mechanism or install new components as necessary, PL 12.25.
7. Enter dC330 code 012-252. Use a piece of paper to actuate the eject home sensor. The display changes. If YES, go to 17. If NO, go to 8.
8. Check the connections of P/J8700 and P/J8725. The connectors are good. If YES, go to 10. If NO, go to 9.
9. Secure the connections.
10. Check for an open or short circuit between P/J8700 and P/J8725. The wiring is good. If YES, go to 12. If NO, go to 11.
11. Repair the open or short circuit.
12. Measure the voltage between the finisher PWB P/J8700 pin 9 (+) and ground (-). The voltage is approximately +5VDC. If YES, go to 14. If NO, go to 13.
13. Check the +5VDC circuit.
14. Measure the voltage between the finisher PWB P/J8700 pin 2 (+) and ground (-). Use a piece of paper to actuate the eject home sensor. The voltage changes. If YES, go to 16. If NO, go to 15.
15. Install a new eject home sensor, PL 12.26 Item 9.
16. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
17. Enter dC330 code 012-054 and 012-056 alternately. The eject motor runs. If YES, go to 27. If NO, go to 18.
18. Check the connections of P/J8706 and P/J8741. The connectors are good. If YES, go to 20. If NO, go to 19.
19. Secure the connections.
20. Check for an open or short circuit between P/J8706 and P/J8741. The wiring is good. If YES, go to 22. If NO, go to 21.
21. Repair the open or short circuit.
22. Measure the voltage between the finisher PWB P/J8706 pin 13 (+) and ground (-), and between P/J8706 pin 15 (+) and ground (-). The voltage is approximately +24VDC. If YES, go to 24. If NO, go to 23.
23. Check the +24VDC circuit. Refer to Chapter 7 Wiring Data.
24. Check the eject motor drive mechanism for deformed parts, broken parts, and/or belt damage The drive mechanism is good. If YES, go to 26. If NO, go to 25.
25. Repair defects or damage to the drive mechanism. Install new components as necessary, PL 12.25.
26. Install a new eject motor, PL 12.25 Item 15. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
27. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON: BSD 12.6 Integrated Office Finisher Set Eject (1 of 2)
Initial Actions
NOTE: Ensure the correct RAP is performed, refer to the 012-161 Set Eject Jam Entry RAP
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Check the eject home sensor, PL 12.26 Item 9 is correctly installed, not broken, and has no foreign object.
• Switch off, then switch on the machine, GP 10.
Procedure
1. Check the specification of the paper, GP 15. The paper is in specification. If YES, go to 3. If NO, go to 2.
2. Load paper that is in specification.
3. Check the condition of the paper. The paper is in normal condition without any problem that causes the paper to be bent or caught. If YES, go to 5. If NO, go to 4.
4. Resolve any problem that causes the paper to be bent or caught.
5. Check the eject mechanism, PL 12.25 for deformed parts, broken parts, and/or belt damage. The eject mechanism is good. If YES, go to 7. If NO, go to 6.
6. Repair the eject mechanism or install new components as necessary, PL 12.25.
7. Enter dC330 code 012-252. Use a piece of paper to actuate the eject home sensor. The display changes. If YES, go to 17. If NO, go to 8.
8. Check the connections of P/J8700 and P/J8725. The connectors are good. If YES, go to 10. If NO, go to 9.
9. Secure the connections.
10. Check for an open or short circuit between P/J8700 and P/J8725. The wiring is good. If YES, go to 12. If NO, go to 11.
11. Repair the open or short circuit.
12. Measure the voltage between the finisher PWB P/J8700 pin 9 (+) and ground (-). The voltage is approximately +5VDC. If YES, go to 14. If NO, go to 13.
13. Check the +5VDC circuit.
14. Measure the voltage between the finisher PWB P/J8700 pin 2 (+) and ground (-). Use a piece of paper to actuate the eject home sensor. The voltage changes. If YES, go to 16. If NO, go to 15.
15. Install a new eject home sensor, PL 12.26 Item 9.
16. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
17. Enter dC330 code 012-054 and 012-056 alternately. The eject motor runs. If YES, go to 27. If NO, go to 18.
18. Check the connections of P/J8706 and P/J8741. The connectors are good. If YES, go to 20. If NO, go to 19.
19. Secure the connections.
20. Check for an open or short circuit between P/J8706 and P/J8741. The wiring is good. If YES, go to 22. If NO, go to 21.
21. Repair the open or short circuit.
22. Measure the voltage between the finisher PWB P/J8706 pin 13 (+) and ground (-), and between P/J8706 pin 15 (+) and ground (-). The voltage is approximately +24VDC. If YES, go to 24. If NO, go to 23.
23. Check the +24VDC circuit. Refer to Chapter 7 Wiring Data.
24. Check the eject motor drive mechanism for deformed parts, broken parts, and/or belt damage The drive mechanism is good. If YES, go to 26. If NO, go to 25.
25. Repair defects or damage to the drive mechanism. Install new components as necessary, PL 12.25.
26. Install a new eject motor, PL 12.25 Item 15. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
27. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782