How to Fix 012-111 112 126 131 Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
012-111 to 012-131 Horizontal Transport Entrance Sensor Jam RAP
BSD-ON: BSD 13.5 Office Finisher LX Horizontal Transport
012-111 The horizontal transport entrance sensor did not deatuate within the specified time.
012-112 After the fuser exit sensor was actuated, the horizontal transport entrance sensor did not deatuate within the specified time.
012-126 After the horizontal transport entrance sensor was actuated, the horizontal transport entrance sensor did not deactuate within the specified time.
012-131 After the fuser exit sensor was actuated, the horizontal transport entrance sensor did not deatuate within the specified time.
Procedure
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
1. Check the horizontal transport drive rolls, PL 13.08 and nip rolls, PL 13.07 for wear or contamination. Check for obstructions or damage in the paper path. The paper path is good. If YES, go to 3. If NO, go to 2.
2. Clean or install new components as necessary.
3. Enter dC330 code 012-190. Actuate the horizontal transport entrance sensor, PL 13.08 Item 6. The display changes. If YES, go to 11. If NO, go to 4.
4. Check the wiring between J8861 pin 2 and P8987 pin 6 for an open or short circuit, or a loose or damaged connector. The wiring is good. If YES, go to 6. If NO, go to 5.
5. Reconnect or repair as necessary.
6. Measure the voltage between P8987 pins 4 and 5 on the finisher PWB. The voltage is approximately +5VDC. If YES, go to 8. If NO, go to 7.
7. Install a new finisher PWB, PL 13.45 Item 2.
8. Measure the voltage between P8987 pin 6 on the finisher PWB and ground. Actuate the horizontal transport entrance sensor. The voltage changes. If YES, go to 10. If NO, go to 9.
9. Install a new horizontal transport entrance sensor, PL 13.08 Item 6.
10. Install a new finisher PWB, PL 13.45 Item 2.
11. Switch off the machine, GP 10. Open the horizontal transport top cover. Cheat the horizontal transport interlock sensor. Switch on the machine, GP 10. The horizontal transport belt is driven. If YES, go to 17. If NO, go to 12.
12. Check the wiring between P/J8862 on the horizontal transport motor and P8987 on the finisher PWB for an open or short circuit, or a loose or damaged connector. The wiring is good. If YES, go to 14. If NO, go to 13.
13. Reconnect or repair as necessary.
14. Measure the resistance of the horizontal transport motor between P/J8862 pins 1, 2, 5 and 6. The resistance is approximately 20 Ohms. If YES, go to 16. If NO, go to 15.
15. Install a new horizontal transport motor, PL 13.08 Item 13.
16. Install a new finisher PWB, PL 13.45 Item 2. If the fault persists, install a new horizontal transport motor, PL 13.08 Item 13.
17. Check the horizontal transport entrance sensor and horizontal transport Motor circuits for an intermittent condition. If the fault persists, install a new finisher PWB, PL 13.45 Item 2.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON: BSD 13.5 Office Finisher LX Horizontal Transport
012-111 The horizontal transport entrance sensor did not deatuate within the specified time.
012-112 After the fuser exit sensor was actuated, the horizontal transport entrance sensor did not deatuate within the specified time.
012-126 After the horizontal transport entrance sensor was actuated, the horizontal transport entrance sensor did not deactuate within the specified time.
012-131 After the fuser exit sensor was actuated, the horizontal transport entrance sensor did not deatuate within the specified time.
Procedure
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
1. Check the horizontal transport drive rolls, PL 13.08 and nip rolls, PL 13.07 for wear or contamination. Check for obstructions or damage in the paper path. The paper path is good. If YES, go to 3. If NO, go to 2.
2. Clean or install new components as necessary.
3. Enter dC330 code 012-190. Actuate the horizontal transport entrance sensor, PL 13.08 Item 6. The display changes. If YES, go to 11. If NO, go to 4.
4. Check the wiring between J8861 pin 2 and P8987 pin 6 for an open or short circuit, or a loose or damaged connector. The wiring is good. If YES, go to 6. If NO, go to 5.
5. Reconnect or repair as necessary.
6. Measure the voltage between P8987 pins 4 and 5 on the finisher PWB. The voltage is approximately +5VDC. If YES, go to 8. If NO, go to 7.
7. Install a new finisher PWB, PL 13.45 Item 2.
8. Measure the voltage between P8987 pin 6 on the finisher PWB and ground. Actuate the horizontal transport entrance sensor. The voltage changes. If YES, go to 10. If NO, go to 9.
9. Install a new horizontal transport entrance sensor, PL 13.08 Item 6.
10. Install a new finisher PWB, PL 13.45 Item 2.
11. Switch off the machine, GP 10. Open the horizontal transport top cover. Cheat the horizontal transport interlock sensor. Switch on the machine, GP 10. The horizontal transport belt is driven. If YES, go to 17. If NO, go to 12.
12. Check the wiring between P/J8862 on the horizontal transport motor and P8987 on the finisher PWB for an open or short circuit, or a loose or damaged connector. The wiring is good. If YES, go to 14. If NO, go to 13.
13. Reconnect or repair as necessary.
14. Measure the resistance of the horizontal transport motor between P/J8862 pins 1, 2, 5 and 6. The resistance is approximately 20 Ohms. If YES, go to 16. If NO, go to 15.
15. Install a new horizontal transport motor, PL 13.08 Item 13.
16. Install a new finisher PWB, PL 13.45 Item 2. If the fault persists, install a new horizontal transport motor, PL 13.08 Item 13.
17. Check the horizontal transport entrance sensor and horizontal transport Motor circuits for an intermittent condition. If the fault persists, install a new finisher PWB, PL 13.45 Item 2.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782