Articles

01C +24VDC Power Fault RAPBSD-ON: BSD 1.2 Main Power On (2 of 2)BSD-ON: BSD 1.5 DC Power Generation (2 of 2)ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.WARNING: Take care when measuring AC mains (line) voltage. Electricity can cause death or injury.1. Check the voltage between the LVPS (P/J501 pin 1) and ground. +24VDC is measured. If YES, go to 7, if NO, go to 2.2. Check the voltage between...

01B +5VDC Power Fault RAPBSD-ON: BSD 1.2 Main Power On (2 of 2)BSD-ON: BSD 1.4 DC Power Generation (1 of 2)ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.WARNING: Take care when measuring AC mains (line) voltage. Electricity can cause death or injury.1. Check the voltage between the LVPS (P/J501 pin 8) and ground. +5VDC is measured. If YES, go to 7, if NO, go to 2.2. Check the voltage between P1...

Power RequirementsRefer to Table 1. Table 1 Electrical power requirements Nominal Voltage Average Current Comments 110-120VAC(60Hz) Plus 6%minus 10% Less than or equal to 12A RMS. 50/60Hz plus 3% minus 3% 220-240VAC(50Hz) Plus 10%minus 10% Less than or equal to 8A RMS. 50Hz plus 3% minus 3% Power ConsumptionRefer to Table 2. Table 2 Power consumption Region Voltage Power Consumption Value (kW) XC 110-127VAC 110VAC - 1.45 or less127VAC - 1.67 or less XE 220-240VAC 220VAC - 1.76 or less240VAC - 1.92 or less Operation ModesRefer to Table 3 and Table 4. Table 3 Operation modes Mode State Run Normal...

01A AC Power RAPBSD-ON: BSD 1.1.Main Power On (1 of 2)BSD-ON: BSD 1.2 Main Power On (2 of 2)Use this procedure to identify AC power input and output failures.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.WARNING: Take care when measuring AC mains (line) voltage. Electricity can cause death or injury.1. Switch off the main power switch, GP 10. Check the voltage between J10 and J18 on the inlet GFI breaker....

003-702 Different Magnification RAP003-702 Different magnification settings, for side 1 and side 2 of a document.ProcedurePerform the steps that follow:1. Advise the customer to correct the magnification settings.2. If the fault persists, reload the software, GP 4.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749...