Articles

013-306 Booklet Safety Switches Open RAPBSD-ON: BSD 13.4 Office Finisher LX Booklet Interlock Switching013-306 Control logic senses that one or more booklet safety switch is open.Initial ActionsWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Check dC122 Fault History for a 013-307 fault. If the fault is listed, perform the 013-307 Booklet Left Cover Open RAP.Procedure1. Measure the voltage between P/J8993 pin 3 on the booklet PWB and ground. +24VDC is measured....

013-210, 013-211 Booklet Staple Move Home Sensor Fail RAPBSD-ON: BSD 13.16 Office Finisher LX Booklet Staple Positioning013-210 Booklet staple move home sensor does not actuate within designated time period.013-211 Booklet staple move home sensor does not deactuate within designated time period.Initial ActionsWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.• Ensure the staple head is free from obstructions.• Check dC122 Fault History for 013-306 or 013-307 faults. If either fault is...

SCP 5 Final ActionsUse Final Actions to verify the correct operation of the machine and to complete the service call.ProcedurePerform the steps that follow. If a fault is identified, go to SCP 3 Fault Analysis:1. If necessary, re-connect the machine to the customer’s network.2. If necessary, perform GP 13 Network Clone Procedure.NOTE: The clone file will need to be taken whenever the system software is changed.3. Perform the relevant maintenance procedures. Refer to SCP 4 Subsystem Maintenance.4. Ensure that the machine has the latest available software loaded.5. Operate the machine in all modes. Make the copies and prints from all...

012-905 Compiler Tray No Paper Sensor Static Jam RAPBSD-ON: BSD 13.10 Office Finisher LX Tamping and Offset (2 of 2)012-905 Paper remains on the compiler tray no paper sensor.Initial ActionsWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.• Check the paper path for jammed pieces paper.• Clean the compiler tray no paper sensor, PL 13.28 Item 9.Procedure1. Enter dC330 code 012-151. Actuate the compiler tray no paper sensor. The display changes....

012-901 Horizontal Transport Entrance Sensor Static Jam RAP012-901 Paper remains on the horizontal transport entrance sensor.ProcedurePerform the 012-111 to 012-131 Horizontal Transport Entrance Sensor Jam RAP.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749 106R03752 106R03751 106R03750• 106R03745 106R03748 106R03747 106R03746• 106R03765 106R03768 106R03767 106R03766Toner...