Articles

024-969 Different Width Mix Punch RAPBSD-ON: BSD 13.6 Office Finisher LX Punch024-969 Mixed punch paper of different widths was detected while printing in punch mode.Initial ActionsWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.• Check if the specified paper is loaded in the tray.• Switch off, then switch on the machine, GP 10.Procedure1. Cancel punch mode. The fault persists. If YES, go to 3. If NO, go to 2.2. Correct the...

024-968 Stapler/Punch Concurrence RAPBSD-ON: BSD 13.6 Office Finisher LX Punch024-968 Staple position and punch position are the same.Initial ActionsWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.• Check if the specified paper is loaded in the tray.• Switch off, then switch on the machine, GP 10.Procedure1. Cancel staple mode and punch mode. The fault persists. If YES, go to 3. If NO, go to 2.2. Correct the settings.3. Check the connectors...

024-967 Mixed Width Paper RAP024-967 Mixed width was detected with settings only available for stapling the same paper width.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Cancel the stapling job. Refer the customer to the user documentation.2. If the fault persists, perform the steps that follow:a. Switch off, then switch on the machine, GP 10.b. Ensure that all connectors on the drive PWB, PL 1.10 Item...

024-965, 024-966 ATS/APS RAP024-965 The paper specified for printing is not loaded in the tray.024-966 The paper specified for printing cannot be detected.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Reload the relevant paper tray.2. If the fault persists, perform the steps that follow:a. Switch off, then switch on the machine, GP 10.b. Ensure that all connectors on the drive PWB, PL 1.10 Item 4 and...

024-957, 024-974 Interposer RAP024-957 Interposer is empty.024-974 Interposer tray size mismatch.ProcedureFor information only, no service action necessary.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749 106R03752 106R03751 106R03750• 106R03745 106R03748 106R03747 106R03746• 106R03765 106R03768 106R03767 106R03766Toner Chip (For Metered Machine):• 106R03733 106R03736 106R03735 106R03734Drum Chip:•...