Articles

003-701 Duplication Prevention Code RAP003-701 A copy restriction code is detected in the document data.ProcedurePerform the steps that follow:1. Advise the customer not to attempt to copy documents that are restricted.2. If the fault persists, reload the software, GP 4.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East...

003-700 Returned Documents Error RAP003-700 When the originals are ejected, the number of ejected originals is more than the number that were fed.ProcedureReload the originals, then re-run the job.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749 106R03752 106R03751 106R03750• 106R03745 106R03748 106R03747 106R03746• 106R03765...

003-345, 003-346 X PIO Mismatch RAP003-345 When a job fail was received from the IISS, an error of the X hot line was detected.003-345 When IIT image delivered was received from the IISS, an error of the X hot line was detected.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Switch off, then switch on the machine, GP 10.2. Ensure that all connectors on the drive PWB,...

003-344 Hotline Fail RAP003-344 Hotline failure during power on.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Switch off, then switch on the machine, GP 10.2. Ensure that all connectors on the drive PWB, PL 1.10 Item 4 and the ESS PWB, PL 3.10 Item 6 are securely connected. Ensure all surface mounted modules on both PWBs are securely connected.3. Reload the software, GP 4.4. Perform the...

003-320 to 003-343 IISS-ESS Communication Fail RAP003-320 IISS sending error detected by the controller. An abnormal parameter is set as the argument for the send function.003-321 IISS sending error detected by the controller. After commands were sent twice from the controller, the controller could not receive acknowledgment from the IISS.003-322 IISS sending error detected by the controller. After commands were sent twice from the controller, the controller could not receive acknowledgment from the IISS.003-323 IISS sending error detected by the controller. After commands were sent twice from the controller, the controller could not receive acknowledgment from the IISS.003-324 IISS sending...