Articles

041-603, 041-604 Environment Sensors Fail RAP041-603 The value of the temperature sensor exceeds the upper limit.041-604 The value of the humidity sensor exceeds the upper limit.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Switch off, then switch on the machine, GP 10.2. Ensure that the fusing unit exhaust fan and the marking unit fan are operating correctly, refer to:• 042-330 Fuser Exhaust Fan Fail RAP.• 043-344...

041-388, 041-391 Logic Fail RAP041-388 When fatal abnormality was detected in marking control.041-391 Finisher module fatal error was detected.ProcedurePerform the steps that follow:1. Switch off, then switch on the machine, GP 10.2. Reload the software, GP 4.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749...

041-371 Productivity Not Set RAP041-371 Productivity not set.ProcedurePerform the steps that follow:1. Switch off, then switch on the machine, GP 10.2. If the fault persists, perform dC132.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749 106R03752 106R03751 106R03750• 106R03745 106R03748 106R03747 106R03746• 106R03765 106R03768 106R03767...

041-340, 041-341 Drive PWB NVM (EEPROM) Fail RAPBSD-ON: BSD 3.1 PWB Communications (ESS PWB to Drive PWB)041-340 NVM (EEPROM) data abnormality.041-341 NVM (EEPROM) access error.Initial ActionsWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Fault code 041-340 Only. Enter dC131. Check that the NVM values that follow are set to 0:• 740-016 Range Over Chain No• 740-017 Range Over Link No• 740-018 Range Over Chain Link• 740-019 Range Over Value• 740-020 Write...

041-335 Drive PWB F12 Blown RAPBSD-ON: BSD 1.5 DC Power Generation (2 of 2)BSD-ON: BSD 10.5 Fused Paper Exit 2041-335 Drive PWB fuse 12 open circuit was detected.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Check the fuser exhaust fan for overcurrent and overvoltage. Repair the wiring or install new components as necessary.2. After the faulty circuit has been repaired, install a new drive PWB, PL...