Articles

024-985 Bypass Tray Obstructed RAP024-985 Bypass tray stopped due to an obstruction.ProcedureAdvise the customer to ensure the correct paper size or type is loaded in the bypass tray in the correct orientation. Resubmit the job.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749 106R03752 106R03751...

024-982 Stacker Tray Lower Safety RAP024-982 Finisher stacker tray lower safety.ProcedurePerform the 012-213 Stacker Tray Lower Limit Failure RAP.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749 106R03752 106R03751 106R03750• 106R03745 106R03748 106R03747 106R03746• 106R03765 106R03768 106R03767 106R03766Toner Chip (For Metered Machine):• 106R03733 106R03736 106R03735...

024-976, 977, 979 Finisher Staple Error RAP024-976 After the staple motor started forward rotation, the staple home sensor did not turn on within 450ms, and after the staple motor started reverse rotation, the stapler head home sensor turned on within 200ms.024-977 Stapler feed ready fail.024-977 Staple near empty or staple feed failure was detected.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform the steps that follow:1. Install a new staple cartridge...

024-972 Tray 6 Size Mismatch RAPBSD-ON: BSD 7.14 HCF Paper Size Sensing and Tray Set024-972 Tray 6 size mismatch.Initial ActionsWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.• Ensure that the HCF is loaded correctly and the paper guides correctly set.• Switch off, then switch on the machine, GP 10.Procedure1. Enter dC330, code 078-202, HCF size sensor A. Manually actuate the HCF size sensor A, PL 70.60 Item 11. The display...

024-970 Tray 6 Out of Place RAPBSD-ON: BSD 7.14 HCF Paper Size Sensing and Tray Set024-970 Tray 6 out of place.Initial ActionsWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Switch off, then switch on the machine, GP 10.Procedure1. Enter dC330, code 078-204, HCF tray in sensor. Manually actuate the HCF tray in sensor, PL 70.45 Item 3. The display changes. If YES, go to 3. If NO, go to 2.2. Check...