Articles

062-790 Recognition Fail RAP062-790 The document being scanned is prohibited by law.ProcedureAdvise the customer to refer to the Legal Notices in the User Guide to check the types of document available for copying.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749 106R03752 106R03751 106R03750• 106R03745...

062-396 CCD Cable Connection Fail RAP062-396 A CIS flat cable connection error was detected.ProcedurePerform the 060-341 to 060-356 LPH Fault RAP.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.Toner Chip (For North America and West Europe Region):• 106R03741 106R03744 106R03743 106R03742• 106R03757 106R03760 106R03759 106R03758• 106R03737 106R03740 106R03739 106R03738Toner Chip (For South America and East Europe Region):• 106R03749 106R03752 106R03751 106R03750• 106R03745 106R03748 106R03747 106R03746• 106R03765 106R03768 106R03767 106R03766Toner Chip (For Metered Machine):• 106R03733...

062-371, 380, 386, 393 Lamp Illumination Fail RAPBSD-ON: BSD 6.3 Document Illumination and Image Input062-371 Insufficient light from Lamp detected in CCD (during white gradation correction/agc before scan starts)062-380 Insufficient lamp brightness was detected when performing AGC.062-386 A CCD output error was detected when performing AOC.062-393 Write failure to the Shading Memory has occurred.Initial ActionsWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Perform ADJ 60.5 Optics Cleaning Procedure.Procedure1. Check the ribbon...

062-362 X Hard Fail RAP062-362 Hard modification of authentication machine was detected.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.1. Switch off, then switch on the machine, GP 10.2. If the fault persists, install a new ESS PWB, PL 3.10 Item 6.**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**You may be also interested in below toner and drum chip (CRUM) for Xerox...

062-360, 062-389 Carriage Position Fail RAPBSD-ON: BSD 6.2 Carriage Control062-360 Any of the faults that follow was detected:• An error with the count value of the carriage position control.• No IIT registration sensor input during carriage initialization.• Abnormality in detected position of IIT registration sensor.062-389 A Carriage overrun was detected.ProcedureWARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.Refer to the procedures that follow as necessary:• GP 6 How to Check a...